Low-Voltage Distribution

120/208-Volt Electrical Distribution

120/208-volt distribution is commonly supplied as a three-phase, four-wire wye system, providing 208 V phase-to-phase and 120 V phase-to-neutral when the source and circuit arrangement are designed accordingly. The nominal voltage alone does not establish that a particular assembly will fit a project. We manufacture new switchboard equipment and supply new retrofit components to specification, serving Texas from the United States and shipping nationwide. Each quotation depends on review of the actual supply, grounding, fault-current conditions, ratings, and required configuration.

UL 891 switchboardsMADE IN USAFAST lead times
NEW EQUIPMENT. PROJECT FOCUSED.SERVING TEXAS
Electrical switchgear equipment viewed from the side

NEW SWITCHGEAR FOR YOUR PROJECT

MANUFACTURING / EQUIPMENT / TEXAS

How 120/208 V serves a facility

In a typical three-phase, four-wire wye arrangement, the relationship between phase-to-phase and phase-to-neutral voltage supports both 208 V three-phase loads and 120 V single-phase loads. That can make the system useful in commercial buildings where lighting, receptacles, and other line-to-neutral loads share distribution with three-phase equipment. Confirm the source configuration and intended loads rather than assuming every 120/208 V service has the same arrangement.

When planning a new switchboard, identify which loads require single-phase or three-phase power, how circuits are distributed among phases, and whether neutral capacity or other project-specific provisions matter. For an existing installation, provide the one-line diagram and panel or switchboard schedules if available. These documents help establish the intended distribution and expose mismatches between the design documents and the equipment actually connected.

Verify the incoming supply and grounding

A nominal 120/208 V label is not enough to define the incoming electrical supply. Confirm the source’s phase count, wire count, grounding method, and actual voltage configuration with the project engineer or serving utility documentation as applicable. Also identify whether the equipment is service equipment or downstream distribution, since that distinction affects the required arrangement and the information needed to develop a suitable quotation.

Document the grounding and neutral treatment specified for the installation, including the applicable bonding point and any project requirements for neutral switching or isolation. Do not infer these details from an older cabinet label or a general building description. Provide available one-line diagrams, grounding notes, and existing equipment information for review. Installation, inspection, and energization must be handled by qualified personnel using approved project procedures.

Establish available fault current and ratings

The available fault current at the equipment location is a key input to selecting an appropriate assembly and its protective devices. Request the value and calculation basis from the engineer or other qualified source, and identify the point in the system to which it applies. A rating selected without this information may not suit the installation. Include upstream source and transformer details when they are available and relevant to the study.

Compare the documented fault-current conditions with the interrupting ratings of proposed protective devices and the applicable short-circuit ratings of the assembly. These ratings are related but are not interchangeable, and their suitability depends on the specified configuration and coordination approach. We review the supplied project requirements for the quotation; engineering, component selection, and any supporting documentation must be confirmed for each proposed build.

Match equipment voltage and load requirements

Specify the system voltage together with the phase and wire arrangement, rather than listing “208 V” by itself. Identify the required bus arrangement, incoming connection, feeder count, protective-device types, and any space or future provisions that the design calls for. For each load, verify its nameplate voltage and phase requirements. Motors and other equipment rated for a different voltage should not be treated as compatible based only on nominal system voltage.

Also establish the expected load profile, demand assumptions, and any project-defined capacity for future circuits. The appropriate ampacity, device frames, and distribution layout depend on these inputs and on the governing design documents; they cannot be inferred from the voltage designation. Send schedules, drawings, enclosure and access constraints, and applicable project specifications with a pricing request so the proposed new equipment can be scoped accurately.

Plan new equipment and retrofit scope

For a replacement or upgrade, distinguish the new switchboard assembly from new retrofit components intended for an existing installation. Provide the existing manufacturer and model information if known, clear equipment photographs, dimensions, bus and connection details, and device identification. Describe what must remain in service or be retained in the design. Physical fit, electrical compatibility, and available documentation all require project-specific review; apparent similarity is not a substitute for verification.

A retrofit scope should identify whether the work replaces a device, modifies a defined section, or calls for a new assembly, along with the drawings and field measurements that support that scope. We supply new equipment and new retrofit components as the manufacturer. Have qualified personnel collect and verify existing installation information under approved site procedures, without relying on live equipment access or unverified measurements.

Prepare a complete quotation and submittal package

A useful request for pricing includes the one-line diagram, load and device schedules, source and grounding information, available fault current, and the specified voltage and wire configuration. Add enclosure requirements, connection details, required accessories, project standards, and any constraints on installation or service access. Identify the project location in Texas or elsewhere so delivery requirements can be reviewed, while keeping the technical scope separate from shipping arrangements.

State which drawings, component-origin details, ratings, and test documentation the project requires, and identify the review or approval process. Do not assume that a particular standard, certification, component origin, or test record applies to every configuration. UL 891 is a switchboard standard, not a blanket designation for all switchgear; applicable standards and any listing for the proposed assembly must be verified for its specific configuration. Availability and lead time are confirmed during quotation review.

LET'S BUILD SOMETHING

Start with
the details.

Tell us what you’re working on. The more you can share about your project, the better we can begin the conversation.

PROJECT INQUIRY

Request a quote

This form opens your default email application. Your inquiry is sent only when you send the email. You can also email us directly or call our team.

* Required fields

Request a quote