120/240 V Panelboards

120/240-Volt Panelboards

Switchgear Builders Texas manufactures new panelboards to project specifications for customers in Texas and ships nationwide. A 120/240-volt panelboard is commonly applied to a single-phase, three-wire system: two ungrounded conductors provide 240 volts between them, while either conductor and the neutral provide 120 volts. Correct selection depends on confirming the actual utility service, connected loads, protective-device requirements, and available panel configuration—not voltage alone.

UL 891 switchboardsMADE IN USAFAST lead times
NEW EQUIPMENT. PROJECT FOCUSED.SERVING TEXAS
Electrical switchgear cabinets arranged on shipping pallets

NEW SWITCHGEAR FOR YOUR PROJECT

MANUFACTURING / EQUIPMENT / TEXAS

Confirm the service before selecting the panelboard

Start with the service documentation and confirm nominal voltage, phase, number of wires, grounding arrangement, and the source feeding the panelboard. The common 120/240 V arrangement is single-phase, three-wire, with two ungrounded conductors and a neutral. Do not infer this arrangement from a building address, existing panel label, or a description such as “residential voltage”; verify it with the electrical design and serving utility information.

Other utility arrangements can include 120/208 V three-phase, four-wire service or 240 V three-phase systems, which may have different line-to-line and line-to-neutral voltages. These are not interchangeable with a 120/240 V single-phase panelboard. If the project has multiple services, transformers, or existing distribution equipment, identify the specific source and intended loads for each panel before requesting a quote.

Specify phase, neutral, and grounding provisions

For a typical single-phase, three-wire panelboard, the design uses two ungrounded bus legs and a neutral provision for 120 V loads. Provide the one-line diagram or a clear service description, and state whether the neutral is required throughout the panelboard and how the equipment grounding conductors are to be terminated. The system grounding and bonding details must follow the project design and applicable requirements.

Clarify whether the panelboard is service equipment or a downstream distribution panel. That distinction affects the specified neutral-to-ground relationship, incoming connections, and associated equipment provisions. Identify any separately derived source or transformer where applicable. We can build new equipment to the confirmed specification; the engineer of record should establish grounding and bonding requirements rather than relying on assumptions from a prior installation.

Match branch breakers to circuit voltage and load

Branch breaker selection must reflect both the circuit voltage and the connected equipment. A 120 V branch circuit uses line-to-neutral voltage; a 240 V circuit uses line-to-line voltage. For each circuit, provide the intended voltage, pole count, load type, and specified overcurrent protection. A two-pole device is generally needed for a line-to-line circuit, but the final device and configuration must follow the equipment design and applicable requirements.

Also identify any loads requiring a particular breaker function or accessory, such as ground-fault protection, shunt trip, or other project-specified features. Do not treat a breaker’s ampere rating as confirmation that it is suitable for the application; voltage, interrupting capability, panelboard compatibility, and the available fault current all matter. Submit the required electrical design information so the proposed configuration can be reviewed before pricing.

Build a usable circuit schedule

A complete circuit schedule helps align the panelboard layout with installation and future maintenance. Include circuit numbers, load descriptions, voltage, pole count, specified breaker rating, and any dedicated or spare positions. Identify which circuits serve continuous loads, motors, heating equipment, or other loads with special design considerations. Where plans are still developing, mark assumptions and pending loads rather than presenting them as final requirements.

Check the schedule against the one-line diagram, panel location, feeder information, and equipment connection drawings. Confirm the required enclosure type, mounting arrangement, conductor entry direction, and available physical space. For a replacement project, provide accurate existing-panel dimensions and connection details, but specify new panelboard equipment or new retrofit components only. Existing labels and drawings should be reconciled with field-verified information by qualified project personnel.

Plan load distribution across the two legs

On a 120/240 V single-phase, three-wire system, 120 V circuits connect from one ungrounded leg to neutral, while 240 V loads connect across both ungrounded legs. Distribute 120 V loads between the two legs using the project’s calculated demand and design criteria. The goal is an appropriate distribution of load, not a simplistic assumption that every circuit contributes equally or that the connected nameplate totals alone determine operating balance.

Review expected operating conditions as well as the initial schedule: equipment duty cycles, seasonal loads, future circuits, and likely simultaneous operation can affect the design. A schedule that identifies each 120 V load by leg, together with 240 V loads and their connections, gives the engineer a basis for evaluating distribution. Final load calculations, conductor sizing, and protection remain project-specific and must be completed by qualified design professionals.

Prepare a quotation package and verify requirements

For pricing, provide the service description, one-line diagram, panel schedule, specified ratings, enclosure and mounting requirements, incoming and outgoing connection details, and any required accessories. Include the project location in Texas or elsewhere, requested delivery timing, and the applicable submittal or documentation requirements. Availability, engineering, lead time, component origin, and test documentation are reviewed for each quotation; timing and configuration are subject to project review.

We manufacture and supply new equipment using American components as specified by the customer, and we serve Texas from the United States. Component origin and any domestic-content requirement should be stated clearly for review; do not assume that specifying American components establishes independent verification or compliance with a particular purchasing rule. Confirm applicable standards and listing requirements for the proposed configuration. Installation, servicing, testing, and energization require qualified personnel following approved procedures.

LET'S BUILD SOMETHING

Start with
the details.

Tell us what you’re working on. The more you can share about your project, the better we can begin the conversation.

PROJECT INQUIRY

Request a quote

This form opens your default email application. Your inquiry is sent only when you send the email. You can also email us directly or call our team.

* Required fields

Request a quote