Choose the Main Power Circuit Breaker Arrangement
Start by establishing whether the 1200-amp assembly requires a main power circuit breaker, a main-lugs-only arrangement, or another project-defined incoming configuration. A main breaker can provide a disconnecting and protective device at the switchgear; a main-lugs-only design depends on upstream protection and must be evaluated as part of the complete distribution system. Confirm the incoming source, conductor or bus connection, service function, and required breaker operation before requesting pricing.
Breaker selection involves more than the continuous current designation. Provide the required interrupting capability based on the available fault current at the equipment terminals, along with trip-unit functions, sensor or rating requirements, and any need for communications or remote operation. Identify the applicable protection settings and any restrictions imposed by the upstream device. Breaker type, frame, and control features are subject to engineering review for the specified assembly.
Define the 1200-Amp Bus and Incoming Connection
The bus must be coordinated with the intended system voltage, continuous-current duty, fault-current conditions, and enclosure layout. Describe whether the design needs a single main bus, a sectionalized bus, or a tie arrangement, and explain how each section is normally supplied and operated. A tie breaker changes operating and protection considerations; it should not be treated as a simple space option. Confirm the intended normal configuration and any permitted alternate source or transfer sequence.
Specify the incoming conductor entry, phase arrangement, neutral requirements, grounding approach, and termination orientation required by the drawings and site plan. Cable space and access can affect enclosure dimensions and field connections, so include conductor sizes and quantities when established by the electrical design. Also identify the required bus material and any project-specific barriers or provisions. Final bus and connection details require review against the assembly design and applicable standards.
Plan Feeder Breakers Around Real Loads
List each outgoing feeder by function, design load, connected equipment, and required protective-device characteristics. The 1200-amp main rating does not determine feeder quantities or ratings: branch circuits may call for different breaker frames, trip functions, poles, or connection arrangements. Indicate which loads are continuous, motor-related, sensitive, or operationally critical, and note planned spare ways separately from active feeders. This makes it possible to evaluate section layout and breaker placement against the actual schedule.
For each feeder, provide the system voltage, load information, conductor termination needs, and any coordination or monitoring requirements defined by the project. Identify whether downstream equipment expects a particular trip unit, auxiliary contact, communication capability, or accessory. If load growth is anticipated, describe the intended future feeder capacity and space strategy rather than assuming vacant positions can later accept any device. Feeder configuration, component availability, and engineering suitability are confirmed during quotation review.
Submit Available-Fault-Current Information
Available fault current is essential to evaluating breaker interrupting capability and the equipment’s short-circuit design basis. Provide the calculated value at the proposed switchgear location, the calculation method or study reference, and the source characteristics used, including transformer data and relevant upstream protective devices. If the value is not final, identify the responsible engineer and expected basis for confirmation. Do not substitute a service rating or a nominal system voltage for a fault-current study.
Fault contribution can change with source configuration, transformer changes, parallel sources, or generator operation. Include operating cases that affect the switchgear, such as normal and alternate feeds, closed or open bus ties, and on-site generation where applicable. State whether a coordination or arc-flash study is available and whether the equipment must accommodate a defined future condition. We review submitted information for the proposed configuration; final suitability and documentation must be confirmed for the project.
Coordinate Protection Across Main and Feeders
Protection coordination depends on the characteristics and settings of upstream, main, tie, and feeder devices—not on the 1200-amp rating alone. Share the latest one-line diagram, protective-device schedule, and coordination study when available. Identify the coordination objectives and any project constraints, such as selective operation for designated loads or limits on permitted trip settings. If settings are still under development, make that clear so the quotation can distinguish confirmed requirements from items awaiting engineering decisions.
Check that the proposed breaker functions and adjustable ranges can support the study’s intended settings, while also considering conductor protection and equipment limitations. A coordination goal does not establish that every device combination will achieve it; the engineer of record should evaluate the complete system and confirm settings. If a tie breaker or alternate source changes available fault current, provide the relevant cases for review. Installation, adjustment, testing, and energization require qualified personnel following approved procedures.
Specify New Equipment, Retrofit Scope, and Submittals
This page concerns new 1200-amp switchgear and new retrofit components only. For a new assembly, provide the one-line diagram, equipment schedule, enclosure and access constraints, incoming and outgoing connection details, and required accessories. For a retrofit involving new components, identify the existing equipment manufacturer and model, compartment dimensions, bus and connection details, and the intended scope. Do not assume a new breaker or component will fit or function with existing gear without dimensional and electrical review.
Include the project location in Texas, requested ship-to details, required submittal documents, and the decision dates that affect procurement planning. We manufacture and supply new equipment to specification, using American components as specified by the customer; component origin and documentation must be confirmed for each quotation. We can review requests for pricing after assessing the design information. Availability, engineering, lead time, applicable standards, listing status for the configuration, and test documentation are confirmed project by project.
