1200-Amp Switchboards

1200-Amp Switchboards

A 1200-amp switchboard is a project-specific assembly, not a complete design description on its own. We manufacture new switchboards to specification for customers in Texas and ship nationwide, with configuration, component availability, engineering, lead time, and documentation confirmed during quotation review. A useful scope identifies the service arrangement, incoming source, feeder schedule, site conditions, and required ratings. UL 891 applies to switchboards; listing and applicable standards must be verified for the proposed configuration.

UL 891 switchboardsMADE IN USAFAST lead times
NEW EQUIPMENT. PROJECT FOCUSED.SERVING TEXAS
Electrical switchgear equipment viewed from the side

NEW SWITCHGEAR FOR YOUR PROJECT

MANUFACTURING / EQUIPMENT / TEXAS

Define the 1200-Amp Section Layout

Start by showing how the 1200-amp assembly will be divided into sections and what each section must contain. Identify the incoming service or source section, distribution sections, metering or control compartments, and any provisions for future feeders. Provide the available equipment-room dimensions, access and working-space constraints, cable-entry direction, and the intended lineup orientation. These details shape a buildable arrangement and help expose conflicts before the quotation is finalized.

Clarify whether the 1200-amp designation refers to the main device, the switchboard bus, or both. Those ratings are related but are not interchangeable, and the selected arrangement must be coordinated with the one-line diagram and project requirements. Mark which sections must remain accessible for inspection or maintenance, and indicate any restrictions on conduit locations, barriers, or compartment separation. We review these inputs against the requested configuration rather than assuming a standard lineup.

Coordinate the Main Protective Device

Specify the intended main-device type and its required functions, such as a circuit breaker or fusible switch, along with the project’s trip, sensing, and coordination expectations. The correct choice depends on the source, available fault current, downstream equipment, protection study, and operating requirements. Include the electrical one-line and, when available, protective-device coordination and arc-flash study criteria so that device selection can be reviewed in context.

State whether the project requires adjustable protection, ground-fault functions, metering interfaces, shunt trip, or other control features, and identify the signals or accessories needed by the facility. Do not assume a particular trip unit, frame, or accessory is included simply because the assembly is rated 1200 amps. The quotation should identify the proposed main-device configuration and any open engineering decisions; final settings and field implementation belong to qualified personnel working under approved procedures.

Build the Feeder Schedule Around Loads

Provide a feeder schedule that lists each outgoing circuit’s load or served equipment, requested protective-device type and rating, pole count, and required accessories. Include spare and future positions explicitly, distinguishing an installed device from a space or provision for later work. This makes it possible to review section allocation, device arrangement, and the relationship between the feeder schedule and the 1200-amp distribution bus without treating unused capacity as a guaranteed future rating.

Identify feeder requirements that affect coordination or physical layout, including ground-fault protection, remote operation, control wiring, metering, and cable landing needs. For motor loads, large transformers, or other equipment with distinctive starting or inrush characteristics, provide the relevant project data and protection criteria. The final device selection should align with the electrical design and applicable studies; a nominal feeder rating alone does not establish suitable protection or coordination.

Specify Bus Capacity and Material

A 1200-amp bus designation should be accompanied by the required bus arrangement and project operating conditions. Specify the phase and neutral configuration, whether a full-capacity neutral is required, and whether a separate equipment grounding bus or other grounding provisions are needed. State any required bus material, plating, bracing, or temperature and enclosure conditions when these are controlled by the project documents. We review the requested details for the quoted assembly rather than assuming a particular construction.

Bus capacity must be considered alongside the main device, connected loads, feeder distribution, ambient and enclosure conditions, and any project-specific requirements. Provide the load calculation or design basis and identify anticipated load growth if it affects the requested configuration. Do not infer spare capacity solely from the 1200-amp label: the bus, protective devices, and load schedule must be evaluated together. Any proposed deviations or unresolved selections should be identified for engineering review.

Resolve Terminations and Cable Entry

Termination requirements can determine the dimensions and arrangement of the incoming and feeder sections. For each connection, provide conductor material, quantity, size range, insulation or lug constraints when specified, and whether conductors enter from the top or bottom. Identify the source and destination of each set, the routing approach, and available bending and pulling space. These details help establish suitable landing provisions and reduce the risk of a mismatch between the switchboard and field-installed conductors.

Document any project requirements for compression or mechanical lugs, lug kits, neutral connections, grounding connections, or cable supports. Confirm whether the specified conductors and termination hardware are compatible with the proposed device and assembly configuration. If conduit stub-up locations or existing infrastructure limit the lineup, share drawings and dimensions early. We supply new equipment and new retrofit components only; retrofit scope must identify the replacement components and the existing interface that they must fit.

Document Short-Circuit and Project Requirements

Provide the available short-circuit current at the switchboard location and the source information used to establish it, including relevant transformer and upstream protective-device data when available. State the required short-circuit rating and whether the project specifies an assembly rating or a rating dependent on a particular upstream protective device. These values are project design parameters: they must be reviewed against the proposed device combination and configuration, not inferred from the 1200-amp current rating.

For a useful quotation, submit the one-line diagram, feeder schedule, equipment-room constraints, applicable specifications, and any required short-circuit or coordination study information. Identify requested inspection, test, and documentation requirements so their applicability can be confirmed for the configuration. UL 891 is the switchboard standard, but a specific listing, label, rating, or test document must not be presumed; verify applicable standards and documentation for the quoted assembly. Installation, testing, and energization require qualified personnel following approved procedures.

LET'S BUILD SOMETHING

Start with
the details.

Tell us what you’re working on. The more you can share about your project, the better we can begin the conversation.

PROJECT INQUIRY

Request a quote

This form opens your default email application. Your inquiry is sent only when you send the email. You can also email us directly or call our team.

* Required fields

Request a quote