Plan the 2500-Amp Section Arrangement
Start with the electrical one-line diagram, service entrance details, and the physical space available for the lineup. Identify the incoming source, main-device position, feeder quantities, outgoing directions, metering needs, and any future provisions. These details determine how the 2500-amp capacity is arranged across sections and whether the proposed lineup can accommodate the required equipment and cable access.
For a new installation or replacement, provide room dimensions, working-space constraints, conduit entry locations, and any restrictions on shipping or moving sections into the building. Clarify whether the switchboard must align with existing gear or connect to other assemblies. We review these project conditions when developing a configuration; dimensions, section count, and layout must be confirmed against the approved drawings.
Select Main and Feeder Protective Devices
The main protective device and feeder devices should reflect the service arrangement and actual load schedule. Define the required device types, ampere ratings, poles, trip functions, and any adjustable settings needed for the design review. Also identify whether the main is to be breaker-based or another specified arrangement, and whether metering, shunt functions, or other control features are part of the scope.
Coordinate device selection with the project’s protection and coordination study rather than assuming that a 2500-amp bus determines every breaker rating. Provide available study information, upstream device data, downstream equipment requirements, and the intended system voltage. Device availability, engineering suitability, and settings support are confirmed for each quotation. Final selection and coordination remain subject to the project’s engineering review and approved design.
Define Bus Capacity and Configuration
Specify the required bus ampacity and configuration for the full assembly, including phase and neutral arrangements, grounding provisions, and any separately required bus features. The 2500-amp designation describes a key design parameter, but the complete bus design must also align with the system configuration, enclosure arrangement, ambient conditions, and project specifications. State any required bus material or treatment instead of relying on an unstated default.
Document the continuous-load assumptions, diversity or demand basis used in the design, and any future feeder capacity the owner expects to reserve. Confirm whether the neutral must be full-sized or otherwise designed to the project requirements, and describe grounding and bonding expectations. We review these inputs as part of the proposed configuration; final bus details and ratings must be shown in the equipment documentation.
Resolve Cable Terminations Before Quotation
Termination requirements can affect device selection, section dimensions, and conductor routing. For each incoming and outgoing circuit, provide conductor material, quantity, size range, insulation type where specified, and the number of conductors per phase. Identify whether connections are bottom or top entry, the intended conduit locations, and any lug or termination requirements called out by the engineer.
Also clarify whether field-installed conductors approach from below, above, or another direction, and whether cable bending space is constrained by walls, housekeeping pads, or existing services. Do not assume that a standard terminal arrangement will accept the project conductors. The quotation and drawings should identify the proposed termination provisions for review, with final compatibility confirmed against the approved conductor schedule and installation conditions.
Establish the Project Short-Circuit Rating
A 2500-amp switchboard’s short-circuit rating must be selected for the actual system, not inferred from its continuous ampacity. Provide the available fault current at the switchboard, system voltage, source and transformer information, and any upstream protective device data needed for evaluation. If the project specifies a short-circuit current rating or an assembly rating basis, include that requirement with the one-line diagram.
Confirm whether the design relies on a fully rated arrangement or a specifically engineered series-rated combination, and provide the documentation supporting that approach. Device combinations and ratings must be reviewed for the exact configuration; a rating cannot be assumed to transfer between different assemblies. We assess the requested rating during project review and identify applicable documentation and standards for the quoted design.
Specify New Equipment, Documentation, and Delivery
Our scope for this page is new equipment and new retrofit components only. For a replacement project, identify which existing conditions must be matched, which components are being replaced, and what drawings or field information are available. Include the equipment schedule, specifications, one-line diagram, applicable studies, and any owner requirements for labeling, metering, accessories, or documentation so the proposed scope can be evaluated without relying on assumptions.
We build to specification using American components as directed by the customer; component origin and any domestic-content requirements should be stated in the request and confirmed for the quoted configuration. Listing and applicable standards must also be verified for that configuration; UL 891 applies to switchboards, not every switchgear assembly. Availability, engineering, lead time, and test documentation are project-specific. We serve Texas from the United States and ship nationwide.
