Start with cable-compartment fit
For 27 kV-class cable terminations, the first design question is whether the proposed cable and termination can be positioned, supported, and connected within the available compartment. Record usable compartment width, depth, and height, along with the locations of phase connections, barriers, ground points, doors, and obstructions. Distinguish clear working space from overall enclosure dimensions; a compartment’s nominal size does not by itself establish usable termination space.
Provide switchgear drawings or verified field dimensions for a retrofit, including the equipment identification and the affected section. Show cable entry direction, entry openings, support locations, and the intended routing path. Confirm whether existing internal parts will remain or be replaced. We review these details against the requested configuration rather than assuming a new component will fit based on voltage class alone.
Define cable size and quantity
Specify the number of cables per phase and the conductor material, conductor size, insulation type, and overall cable diameter. Include shield or concentric-neutral construction and any armor that affects the termination or grounding arrangement. Where parallel cables are proposed, identify the intended count and phase grouping. Cable size alone is insufficient for checking fit because insulation thickness and jacket dimensions can change the space needed at the termination and along the cable route.
Also clarify whether the cables are single-conductor or part of a different cable assembly, how they enter the compartment, and whether cable supports are part of the requested scope. For a retrofit, provide cable manufacturer data when available or measured outside diameter if the original records are incomplete. Confirm that the proposed termination is compatible with the actual cable construction and the project’s electrical requirements.
Choose compatible stress control
Termination stress control manages the electrical field where the cable’s insulation shield ends. The appropriate method depends on the cable insulation system, shield design, conductor dimensions, operating conditions, and the connection arrangement. Identify the intended termination family and provide the cable preparation and accessory requirements available from the cable or component documentation. Do not select a termination solely because its nominal voltage class matches the switchgear designation.
For new equipment or new retrofit components, the quotation review should establish which termination components are included and which are supplied or prepared by others. Confirm interface dimensions, connection hardware, insulation compatibility, and any required shields or protective parts. If documentation is incomplete, identify the unknowns before release for manufacture. Installation, inspection, and any required testing must be performed by qualified personnel under approved project procedures.
Plan bend radius and cable routing
Cable routing must respect the minimum bend radius specified for the actual cable and termination system. Check the full path from the cable entry to the electrical connection, not just the bend immediately below the termination. Account for cable stiffness, the number of conductors, support spacing, and the space needed to form a stable route without forcing the cable against a barrier, door, or adjacent phase.
Provide the cable manufacturer’s bend-radius requirement and note any pulling or installation constraints that affect the planned route. On retrofit projects, compare the existing route with the proposed cable dimensions before ordering components. A termination that appears to fit at the connection point may still be unsuitable if the cable cannot reach it while maintaining the required bend radius and clearance.
Coordinate grounding and phase clearances
State how cable shields, concentric neutrals, or other conductive layers are to be grounded, and identify the intended ground connection points. The grounding arrangement must be coordinated with the cable design, switchgear configuration, and project grounding scheme. Provide relevant drawings or requirements so the connection path and hardware can be reviewed. Do not assume that an existing ground point is suitable for a changed cable quantity or retrofit arrangement.
Phase-to-phase and phase-to-ground clearances depend on the complete termination geometry, including cable position, connection hardware, insulation profiles, and barriers. Submit the applicable project requirements and drawings for review rather than relying on a generic spacing assumption. Changes to conductor orientation or parallel-cable layout can affect clearances. The final configuration and applicable standards should be verified for the specific assembly; UL 891 applies to switchboards and is not a blanket standard for all switchgear.
Prepare a complete quotation package
A useful request for pricing identifies whether the scope is new switchgear or new retrofit components, the 27 kV-class application, cable data, quantity per phase, termination requirements, grounding approach, and dimensional constraints. Attach one-line diagrams, compartment drawings, cable data sheets, and photographs where available. Mark dimensions that are confirmed and distinguish them from estimates. Include the project location in Texas or elsewhere so shipping requirements can be reviewed.
Before approval, review the quotation for included components, engineering assumptions, required customer-supplied information, and the documents expected with the order. Component origin, availability, lead time, and test documentation must be confirmed for the quoted configuration. Customers may specify American components; origin and any domestic-content requirements should be addressed explicitly in the project review and quotation, without assuming independent verification or compliance. Request pricing once the configuration and open questions are clearly stated.
