Define the Sectionalizing Boundary and Isolation Goal
First identify exactly what a sectionalizing point must separate: a utility or generator source, a main bus, a branch feeder, a transformer connection, or a downstream distribution section. Mark the intended boundary on the one-line diagram and show every normal and alternate connection. This makes it possible to distinguish feeder isolation from source transfer or bus sectionalizing, which may require different switching devices and interlocking logic.
Describe the operating outcome rather than relying only on a product name. Can one feeder be isolated while other feeders remain supplied? Must a bus section be disconnected for maintenance? Is the system designed for open-transition source transfer, or is parallel operation intended? These answers shape the arrangement, device functions, and controls. We review them with the project documents before confirming a configuration or pricing.
Coordinate Feeder Isolation With Protection
For each outgoing feeder, provide its destination, connected equipment, protective-device requirements, and expected fault-clearing coordination. Identify whether the sectionalizing device is intended to interrupt load current, provide isolation after an upstream protective device clears a fault, or perform another defined duty. A switch, interrupter, and circuit breaker are not interchangeable descriptions; the required function and applicable ratings must be established for the proposed assembly.
Include available short-circuit information, system grounding method, protection settings or study assumptions, and any coordination constraints from upstream and downstream equipment. These inputs help the design team evaluate interrupting and withstand requirements, protective functions, and the boundary between switchgear and external relaying. Final device selection depends on the system study and configuration review, not simply the nominal voltage or number of feeders.
Plan Cable Routing Before Fixing the Compartment Layout
Cable entry and exit locations can determine the practical switchgear arrangement. Show whether medium-voltage cables approach from above, below, or another direction, and identify conduit or duct-bank locations, bend-space limits, pulling access, and termination preferences. For each circuit, provide cable quantity, conductor and insulation information, approximate route, and termination details when available. These details help assess compartment placement and whether the proposed cable paths are workable.
Consider how cable routing affects separation between circuits, access to terminations, and the ability to isolate the intended feeder without disturbing other sections. Identify spare or future feeder positions and whether future cables will enter through reserved space or a separate route. Do not assume that a future connection can be added without changes to the lineup or site infrastructure. Confirm clearances, termination arrangements, and site interface requirements during project engineering.
Document the Switching Sequence and Interlocks
Provide the intended normal lineup state and a written sequence for planned transfers, feeder isolation, and restoration. State which devices are normally open or closed, which sources may be available simultaneously, and what conditions must be satisfied before an operation is permitted. A clear sequence exposes conflicting states early, such as closing a tie while both sources remain connected when parallel operation is not allowed.
Identify required key, mechanical, electrical, or supervisory interlocks, along with status indication and remote-control expectations. The sequence should be checked against the one-line diagram, protection scheme, and operating procedures by the responsible engineering and operations teams. Interlocks can prevent specified device combinations, but they do not replace approved procedures or qualified personnel. Installation, servicing, testing, and energization must be performed by qualified personnel under approved procedures.
Resolve Source Configuration and Alternate Feeds
Sectionalizing design changes substantially with the source arrangement. Document whether the lineup receives power from one utility source, separate utility feeds, generators, transformers, or a combination. Show source grounding, transformer connections when known, tie points, and the intended transfer method. If sources can operate in parallel, identify that requirement explicitly and provide the protection and control basis; do not infer parallel capability from a tie-switch location alone.
For each source and tie condition, define which sections are energized and what must remain isolated. Explain whether transfer is manual or controlled, whether automatic logic is required, and what source-availability signals are provided by others. These details help align the switchgear arrangement with the system architecture and prevent assumptions about controls or external equipment. Source ratings, device duties, and the final operating scheme require project-specific engineering review.
Specify New Equipment or a New Retrofit Component
For a new lineup, submit the latest one-line diagram, load and fault-study information, feeder schedule, site cable plan, control requirements, and applicable project specifications. Identify the requested medium-voltage class and system parameters as design inputs, not as confirmation that a particular configuration is available. We manufacture new equipment to specification; engineering scope, component origin, documentation, and lead time are reviewed and confirmed for each quotation.
For a retrofit, provide the existing equipment manufacturer and model information, nameplate and compartment details, drawings, photographs, and the function of the component to be replaced. State whether the project seeks a new replacement device or another new retrofit component, and document all relevant mechanical, electrical, and control interfaces. Compatibility cannot be determined from a brief description alone. We supply new equipment and new retrofit components; configuration and applicable standards must be verified before purchase.
