Choose the Main Power Circuit Breaker Arrangement
Start by identifying how the 800-amp main will connect to the source and operate within the distribution system. The design may call for a main breaker, a main-and-tie arrangement, or another specified lineup configuration. Clarify whether the main is intended for service entrance or downstream distribution use, how sources are arranged, and whether transfer or tie operation is part of the project. These are design inputs, not assumptions to resolve after quotation.
Provide the one-line diagram and identify the source transformer or upstream device, nominal system voltage, phase and wire configuration, and intended operating sequence. For a tie breaker, describe which sources can be connected and whether concurrent operation is permitted. The manufacturer can review the requested arrangement against the project requirements, but available configurations and applicable standards must be confirmed for the specific assembly.
Size and Configure the Bus for the System
An 800-amp designation does not by itself define every bus characteristic. Specify the required bus rating and configuration, including the main bus, feeder connections, neutral treatment where applicable, and grounding provisions. Identify whether the design calls for a particular bus material or arrangement, and communicate any project constraints affecting section layout, incoming cable access, or future connection points. The selected design must be reviewed as a complete assembly.
Document the system voltage and grounding method, the source and load connection locations, and any requirements for top or bottom entry. A one-line diagram, equipment layout, and cable information help distinguish electrical requirements from space and routing constraints. Avoid assuming that an existing enclosure or bus arrangement can be reused without engineering review; compatibility depends on the actual equipment and project conditions.
Plan Feeder Breakers Around Actual Loads
Develop the feeder schedule before choosing section layouts. For each outgoing circuit, identify the connected load, intended feeder protection, conductor information when available, and whether the circuit serves a motor, transformer, distribution panel, or other defined load. The number, type, and placement of feeder breakers influence the lineup arrangement and should be considered alongside the 800-amp main rather than treated as interchangeable spaces.
Call out spare or future feeder positions separately from active circuits, and explain what future additions are anticipated. Include any special coordination, monitoring, interlocking, or access requirements in the equipment specification. If the project involves new retrofit components, identify the existing gear manufacturer and model, available drawings, installed device details, and the exact scope requested. Compatibility and replacement suitability require review; do not assume a component fits based on amp rating alone.
Provide Available-Fault-Current Information
The available fault current at the switchgear location is a critical design input. Provide the calculated value and the study basis, including the source transformer data, upstream protective-device information, and relevant conductor or bus impedance where available. State the point in the system where the calculation applies and whether the value reflects a particular source or operating condition. A nominal 800-amp rating does not establish the assembly’s short-circuit suitability.
If fault-current data is incomplete, identify the information still being developed instead of substituting an unsupported estimate. Include the project engineer’s study or calculation when available, and identify any generator, alternate source, or parallel-source conditions that could affect the result. The proposed configuration, ratings, and applicable standards must be reviewed and confirmed for the quotation; do not infer acceptance from a product category or current designation.
Coordinate Protection Across Main and Feeders
Protection coordination depends on the upstream device, the 800-amp main, feeder devices, and downstream equipment. Provide the latest coordination study or the engineer’s required time-current curves, along with the desired selective-coordination boundaries and any constraints on protective settings. Identify which devices are expected to clear faults and any operational priorities, such as maintaining service to unaffected feeder circuits.
Share the specified trip functions, adjustment requirements, communications or monitoring needs, and any restrictions imposed by the project design. Coordination should be evaluated across the actual system, not inferred from breaker frame size or a general equipment description. Confirm the study assumptions and documentation expected with the project team. Protection settings, testing, and energization are matters for qualified personnel working under approved procedures.
Assemble a Complete RFQ and Retrofit Scope
A complete request for pricing should include the one-line diagram, feeder schedule, equipment layout, system voltage and grounding details, available-fault-current data, and protection coordination requirements. Add the requested main and tie arrangement, bus specifications, enclosure or access constraints, and project standards. Identify the delivery destination in Texas or elsewhere so the quotation can address the actual project scope. Engineering, component origin, lead time, and documentation are confirmed for each quotation.
This manufacturer-only offering is for new equipment and new retrofit components. For retrofit components, provide photographs and nameplate or catalog information only as supporting identification, together with drawings and the installation scope. Specify any requested test records and applicable standards. UL 891 applies to switchboards, not automatically to all switchgear; listing and standards must be verified for the proposed configuration.
