Separate the Four Voltage and Insulation Values
Nominal system voltage is the designation of the power system the equipment will serve. It is not, by itself, a complete equipment specification. Equipment maximum voltage is the highest voltage for which the equipment is designed to operate within its applicable conditions. The required relationship between nominal voltage and equipment maximum voltage depends on the system and the equipment standard; confirm both values rather than assuming they are interchangeable.
Power-frequency withstand and BIL describe insulation performance under different forms of electrical stress. Power-frequency withstand concerns applied voltage at power frequency for a specified test condition. BIL, or basic impulse insulation level, addresses a standardized impulse voltage used to characterize insulation withstand. Neither value is another way to state nominal voltage or equipment maximum voltage. Ask the engineer of record to identify the required values and governing standards for the specific assembly.
Establish the System Voltage and Grounding Conditions
Begin the schedule with the nominal system voltage at the equipment connection, not merely the utility service designation or a nearby transformer nameplate. Identify whether the system is three-phase or single-phase, its frequency, and the grounding method, including whether the neutral is solidly grounded, impedance grounded, or ungrounded where applicable. These details help determine which insulation and equipment requirements apply at the intended point of installation.
Also document expected operating voltage range, system configuration, and any relevant source or transformer information available to the design team. A project may have different voltage conditions on the line and load sides, or across separate sections. For Texas projects, provide the project-specific electrical one-line and criteria rather than relying on the state or city name to define the system. We review the supplied design basis before confirming a proposed configuration.
Specify Equipment Maximum Voltage for the Application
Equipment maximum voltage should be stated explicitly for the equipment being quoted. It is a design parameter used to select equipment suitable for the system’s highest applicable operating voltage, not a prediction that the system will continuously operate at that value. The equipment’s construction, insulation system, clearances, and applicable standard all matter. Do not infer this rating from a nominal voltage label or from a different product family.
Ask the responsible engineer to confirm the required maximum voltage and the standard or specification governing its selection. Where an existing installation is being modified, record the existing equipment identification and relevant electrical ratings, but do not assume a replacement component inherits the suitability of the original assembly. We supply new equipment and new retrofit components only; fit, interface, and rating compatibility must be reviewed for the particular application.
Define Power-Frequency Withstand Requirements
Power-frequency withstand is a specified insulation test value under defined conditions, not the normal operating voltage and not a substitute for an equipment maximum-voltage rating. Its meaning depends on the applicable product standard, test method, duration, and insulation configuration. When a project specification gives a withstand value, identify the associated standard and the equipment or circuit to which it applies so the quotation can be reviewed on a consistent basis.
Distinguish insulation withstand from short-circuit current ratings and from routine field commissioning checks. Those address different design or verification questions. Provide any required factory documentation, test scope, and acceptance criteria in the procurement specification. Whether particular test records or other documents are available must be confirmed for the quoted configuration; do not presume that a stated insulation value automatically establishes a particular test report or listing.
Use BIL to Address Impulse Insulation Coordination
BIL represents an impulse insulation level, not the nominal system voltage, equipment maximum voltage, or power-frequency withstand value. It is relevant to insulation coordination and the electrical stresses equipment may encounter. The appropriate requirement depends on the system design, installation conditions, protective devices, and applicable engineering criteria. A schedule that lists BIL without identifying the associated equipment and governing requirements may be ambiguous.
Coordinate the specified BIL with the project’s surge protection and insulation-coordination approach. State the required value and identify which parts of the assembly it applies to, especially where different components or interfaces have different insulation requirements. Do not select a value solely by copying one from equipment operating at another voltage class. The engineering team should resolve the basis and confirm that the requested configuration and supporting documentation are available for quotation.
Scope New Equipment and Retrofit Components Clearly
For a new switchgear package, submit the one-line diagram, equipment schedule, voltage and insulation requirements, and any applicable project specification. Identify the equipment type and intended application, along with installation conditions or interface constraints that could affect the design. For a retrofit component, provide the original equipment manufacturer and identification data, drawings or dimensions, connection details, and photographs where useful. These records support a fit and rating review; they do not guarantee interchangeability.
Our quotations cover new equipment and new retrofit components. Ask us to confirm the proposed configuration, applicable standards, component origin, documentation, and lead time during project review. UL 891 applies to switchboard assemblies, not universally to all switchgear; listing and applicable standards must be verified for the specific configuration. Customers may specify American components, but domestic-content compliance is not implied and must be addressed and confirmed as required for the project. Installation, servicing, testing, and energization require qualified personnel following approved procedures.
