Separate the assembly, bus, and breaker ratings
Start by identifying the continuous-current rating assigned to the complete switchboard assembly and the rating of its bus system. These values concern the equipment’s ability to carry current under the conditions and configuration established for the design. They are not interchangeable with the rating printed on an individual breaker, and the lowest applicable limitation can constrain the usable rating of the installed equipment.
When requesting pricing, provide the switchboard identification and drawings if this is a replacement or retrofit, or the one-line diagram and project requirements for new equipment. Ask which rating applies to the complete configuration, including sections, connections, and specified devices. The quotation should make clear what is being supplied and identify any rating or configuration assumptions that need engineering confirmation.
Understand breaker frame and sensor sizes
A breaker frame size describes the breaker family and its design capacity; it does not state the trip point selected for a particular circuit. A sensor, where used, is the current-sensing element associated with the trip unit. Sensor size and trip-unit capabilities affect the available protection settings, but neither alone establishes the continuous-current rating of the switchboard assembly or bus.
For each feeder or main, document the existing or intended breaker manufacturer and type where applicable, frame size, sensor size, poles, and trip-unit type. For new equipment, provide the specified protection requirements rather than assuming that a breaker with a particular frame will fit or coordinate. For a retrofit, confirm physical compatibility, connection details, and device suitability against the actual equipment configuration before selecting new components.
Specify adjustable trip settings deliberately
Adjustable trip settings determine how a breaker responds to sensed current according to its trip-unit functions and selected values. Depending on the device, settings may include long-time pickup and delay, short-time pickup and delay, instantaneous pickup, or ground-fault functions. The available adjustments vary by breaker and trip unit. A setting is not the same as a continuous-current rating, and changing a setting cannot raise the assembly or bus rating.
Provide the intended settings or the engineering basis for selecting them, along with the protective-device coordination study or other project criteria when available. Identify which settings are fixed, adjustable, or required to be field-configured. Proposed values should be reviewed against the system design and protection requirements by qualified personnel. We confirm the offered device’s setting capabilities and configuration as part of project review rather than assuming a particular range is available.
Use load calculations to establish requirements
Load information helps determine the required equipment rating and protection design, but a total connected-load figure alone may not answer either question. Share the load schedule, demand assumptions, continuous and noncontinuous load classifications where applicable, expected operating conditions, and any planned growth allowance. Include system voltage, phase, frequency, source arrangement, and service or feeder function so the proposed assembly can be evaluated in context.
Ask the project engineer to identify the design current used for the assembly and bus selection and the basis for each breaker’s frame, sensor, and trip settings. This makes it easier to spot mismatches, such as a breaker selection that appears adequate in isolation but conflicts with the equipment rating or intended coordination. We review submitted design information for the quoted scope; project-specific calculations and final protective settings remain subject to responsible engineering approval.
Document retrofit details before ordering
A retrofit requires more than matching a breaker’s nominal current. Provide equipment nameplate data, manufacturer and model information, section and bus details, existing breaker identification, connection or mounting information, and clear photographs or drawings where available. Note whether the scope is a replacement breaker, a trip-unit-related component, or another new retrofit component. Existing ratings and settings should be transcribed from reliable equipment records, not inferred from appearance.
Our retrofit scope is new equipment and new components. Before pricing, we check whether the requested component can be specified for the identified equipment and whether additional details are required. Do not assume a component is interchangeable because frame markings or current figures appear similar. Compatibility, protection functions, applicable standards, and any required documentation must be verified for the exact configuration before an order is finalized.
Confirm quotation scope and operating documentation
A useful request for pricing distinguishes the assembly rating, bus rating, breaker frame and sensor sizes, and requested trip settings for each device. Attach the one-line diagram, load data, equipment schedules, relevant drawings, and coordination information, and flag any unresolved design choices. State whether the request is for a complete new switchboard or new retrofit components. These details help us identify what can be quoted and what requires clarification or engineering review.
The quotation should define the proposed equipment and identify assumptions, exclusions, and information still needed. Confirm component origin requirements, requested test or design documentation, and the standards applicable to the specific assembly; availability and documentation are confirmed for each quotation. UL 891 applies to switchboards, not automatically to every switchgear device or configuration, so listing and applicable standards must be verified for the offered design. Installation, servicing, testing, and energization require qualified personnel following approved procedures.
