Electrical Distribution Glossary

Current Transformer: Electrical Distribution Glossary

A current transformer (CT) is an instrument transformer that produces a scaled secondary current corresponding to the current flowing through its primary conductor. Metering systems use that scaled signal to measure load, while protective relays use it to detect conditions such as overcurrent or ground fault. Ratio, polarity, connected burden, and the intended application all matter when selecting a CT for new equipment or a new retrofit component. We serve Texas from the United States and ship nationwide; project-specific availability and engineering are confirmed during quotation.

UL 891 switchboardsMADE IN USAFAST lead times
NEW EQUIPMENT. PROJECT FOCUSED.SERVING TEXAS
Electrical switchgear installed in an equipment room

NEW SWITCHGEAR FOR YOUR PROJECT

MANUFACTURING / EQUIPMENT / TEXAS

What a current transformer does

A CT lets meters and relays work with a reduced current signal rather than carrying the primary circuit current through their measuring inputs. Its primary is connected in series with the circuit, either as a conductor passing through a window or as a winding designed for the application. The secondary provides a proportional signal to compatible instruments. The CT is not a voltage transformer: it responds to current in the primary circuit.

The function depends on the connected device. A metering CT is selected to support the accuracy needed for the specified measurement range, while a protection CT must provide a useful signal under the fault conditions and relay requirements defined by the design. One CT should not be assumed suitable for both jobs without review. Identify whether the point is for revenue or operational metering, protective relaying, or another defined purpose.

Choose the ratio for the actual application

The CT ratio expresses the relationship between primary and secondary current, such as a stated primary-current rating compared with a stated secondary-current rating. For example, a 400:5 ratio represents 400 units of primary current corresponding to 5 units of secondary current at the stated relationship. It does not mean the CT forces the circuit to operate at that current. The primary rating should reflect the design current and expected operating range, while the secondary rating must match the connected meter or relay.

When requesting a quotation, provide the required ratio and explain the expected load range and protection function. Ask whether the proposed ratio supports useful metering resolution at normal load and the response required by the relay scheme. Also confirm whether the design calls for a single ratio or selectable ratio taps, and how any taps are to be connected. A ratio chosen only from the circuit’s nominal rating can produce an unsuitable measurement or protection signal.

Polarity and terminal identification

CT polarity identifies the corresponding instantaneous direction of current at its primary and secondary terminals. Markings such as H1 and H2 on the primary and X1 and X2 on the secondary communicate that relationship according to the applicable drawings and equipment conventions. Correct polarity is important when signals are compared, summed, or used to determine direction. A reversed relationship can affect differential protection, directional elements, metering phase relationships, and residual or ground-fault connections.

Specify the required polarity and terminal markings, and make sure the CT drawing agrees with the one-line diagram, relay diagrams, and phase identification. For a retrofit, document the existing conductor direction and terminal connections before selecting a replacement component; do not assume the existing arrangement follows a standard orientation. Installation, testing, and energization must be performed by qualified personnel using approved procedures and the project documentation.

Burden, accuracy, and connected devices

Burden is the load imposed on the CT secondary by connected instruments, relays, wiring, and terminals. It is commonly expressed in electrical terms specified by the applicable CT data and design. Excessive burden can affect how accurately the secondary reproduces primary current, especially in applications where the CT must respond to elevated fault current. Cable length and conductor size contribute to circuit resistance, so the actual secondary circuit—not just the meter or relay input—must be considered.

Provide the instrument or relay model where known, the secondary-circuit arrangement, and the design requirements for accuracy or protection performance. Ask the engineer of record to confirm the required burden and performance class for the application, including fault-current conditions where relevant. For a new assembly, the CT selection should coordinate with the specified devices and wiring design. For a retrofit, verify that the replacement component is compatible with the existing circuit and available physical space.

CT selection in switchboards and retrofit work

In a new switchboard, CT placement and construction affect conductor routing, phase clearances, access to terminals, and the arrangement of meters or relays. Specify the circuit location, conductor or bus dimensions, number of phases, mounting constraints, and whether the CT is intended for metering, protection, or both. For a switchboard assembly, we review the requested configuration and applicable standards as part of the quotation process; UL 891 applies to switchboards, not automatically to every CT or every switchgear configuration.

A new retrofit CT component requires its own compatibility review. Record the existing CT ratio, polarity, dimensions, mounting method, conductor geometry, terminal arrangement, connected burden, and device requirements where available. If existing records are incomplete, flag the uncertainty rather than treating an unverified marking as a confirmed specification. We supply new equipment and new retrofit components only. Engineering, component availability, and documentation are confirmed for each project.

Information to include in a pricing request

A useful request includes the project location in Texas or elsewhere, equipment type, system voltage, circuit or bus details, intended CT function, required ratio, secondary rating, polarity convention, accuracy or protection requirements, and the connected meter or relay information. Attach the relevant one-line diagram, control or relay drawings, equipment layout, and existing CT data for retrofit work. Identify any preferred American components; component origin and project requirements should be reviewed and confirmed for the specific quotation.

Also state whether the request is for a CT within a new switchboard assembly or for a new retrofit component, and describe any schedule, enclosure, access, or documentation constraints. Current and voltage values are project design inputs, not a promise that a particular configuration is available. We review the requested scope before confirming engineering, lead time, component details, and applicable test or standards documentation. Pricing is based on the defined configuration, so clear drawings and complete selection data help establish an appropriate quotation.

LET'S BUILD SOMETHING

Start with
the details.

Tell us what you’re working on. The more you can share about your project, the better we can begin the conversation.

PROJECT INQUIRY

Request a quote

This form opens your default email application. Your inquiry is sent only when you send the email. You can also email us directly or call our team.

* Required fields

Request a quote