Verify motor voltage, phase, and system configuration
Start with the motor nameplate and the electrical one-line, then compare their stated voltage and phase with the distribution source. A typical 347/600 V arrangement is a three-phase, four-wire wye system: 600 V is measured phase to phase, while 347 V is measured phase to neutral. Do not assume every motor uses both values or that a motor rated for one voltage can be connected to the other.
For each load, record nameplate voltage, phase, frequency, full-load current, connection diagram, and any dual-voltage or reconnection requirements. Confirm whether the motor is intended for 600 V three-phase service and whether any 347 V loads actually require a neutral. Ask the utility and project engineer to confirm that this voltage and system configuration are available and appropriate at the service point.
Coordinate starters with motor operating requirements
Starter selection depends on more than motor horsepower. Establish the motor’s nameplate current and starting method, the expected starts per hour, driven-load characteristics, acceleration time, and any operational limits on voltage drop or inrush. Confirm whether the design calls for across-the-line, reduced-voltage, or another approved starting arrangement; do not infer a starter type from the distribution voltage alone.
The switchgear scope should identify starter compartments or separately mounted equipment, control voltage, control interface, and any required interlocks or remote commands. Clarify how the starter is connected to upstream and downstream protection, and who supplies associated controls and field wiring. These details let us assess the requested configuration and component availability before preparing a quotation.
Set overload protection from motor data
Overload protection is intended to protect the motor against sustained overcurrent, so its selection and setting must follow applicable requirements, motor nameplate information, and the approved design. Capture the overload device type, adjustment range, reset method, trip class where applicable, and any ambient or operating conditions that affect selection. The motor’s nameplate current—not a generic estimate based only on horsepower—should anchor the review.
Coordinate overload behavior with the starter, motor duty, and control scheme. Determine whether the application needs phase-loss sensitivity, ground-fault functions, temperature inputs, or a specific alarm and trip interface. Have the responsible electrical designer verify settings and coordination. Our equipment is supplied new to specification; final protection choices and settings are confirmed through project engineering rather than assumed from a standard package.
Coordinate branch-circuit and upstream protection
For every motor branch, define the required disconnecting means and short-circuit and ground-fault protection, then coordinate that selection with the starter and overload device. Document the available fault current, equipment interrupting or withstand requirements, conductor assumptions, and the protective-device characteristics used in the study. A branch device that is suitable in isolation may not provide the intended coordination or equipment protection in the complete system.
Provide the one-line diagram, motor schedule, protective-device schedule, and any available coordination or arc-flash study information for review. Identify whether the requested assembly includes branch devices, feeder protection, metering, or only a defined distribution section. The engineer of record must approve the protection scheme and its application to the installation; installation, testing, and energization belong to qualified personnel following approved procedures.
Confirm U.S. supply and component requirements
A 347/600 V project may be specified for a facility or utility arrangement that is not available at every U.S. service location. Confirm the serving utility’s offered voltage, grounding arrangement, service capacity, and connection requirements before finalizing equipment. If the site supply differs from the motor system, identify the required transformation or other engineered solution and assign responsibility for its design and scope.
Specify new equipment and new retrofit components only. If the project requires American components, state that requirement in the inquiry and identify any component categories or documentation expectations. Component origin, availability, and any requested domestic-content documentation must be confirmed for the quoted configuration; an American-component request is not, by itself, a certification of Buy American or other regulatory compliance.
Prepare a complete quotation and submittal package
A useful request for pricing includes the system one-line, service voltage and frequency, grounding details, motor schedule with nameplate data, starter and overload requirements, branch-protection preferences, and available fault-current information. Add enclosure and installation environment, incoming and outgoing cable details, space or interface constraints, metering and control needs, and the project schedule. Mark open engineering decisions rather than presenting estimates as confirmed requirements.
Identify the applicable standards and requested documentation for the exact assembly. UL 891 applies to switchboard assemblies; it is not a blanket listing for all switchgear, starters, or every configuration. Listing status, applicable standards, and test documentation must be verified for the quoted design. We review the scope before confirming engineering, components, availability, and lead time, then provide pricing for new equipment built to the approved specification.
