Service Entrance Equipment

347/600-Volt Service Entrance Equipment

Switchgear Builders Texas manufactures new service entrance equipment to project specifications and serves Texas from the United States, with nationwide shipping. A 347/600 V service is commonly arranged as a three-phase, four-wire wye system, but the actual utility service, available equipment, metering requirements, and approved configuration must be confirmed for each project. We can review the defined scope for new equipment or new retrofit components and provide pricing for a configuration subject to engineering and availability review.

UL 891 switchboardsMADE IN USAFAST lead times
NEW EQUIPMENT. PROJECT FOCUSED.SERVING TEXAS
Electrical switchgear cabinets arranged on shipping pallets

NEW SWITCHGEAR FOR YOUR PROJECT

MANUFACTURING / EQUIPMENT / TEXAS

Coordinate the 347/600 V Service Configuration

A 347/600 V service typically provides 347 V phase to neutral and 600 V phase to phase in a three-phase, four-wire wye arrangement. Do not treat that convention as confirmation of the service at a particular facility. Confirm the utility’s nominal voltage, phase and wire arrangement, grounding method, and service characteristics from utility documentation and the project electrical design before selecting equipment.

For a quotation, identify whether the equipment is for a new service or a defined replacement scope, the service point, system configuration, and the required incoming and outgoing connections. Include the one-line diagram and identify loads or downstream distribution that affect the design. These details help establish a coherent equipment boundary and surface mismatches before equipment is specified.

Resolve Utility Metering Requirements Early

Metering arrangements depend on the serving utility and project conditions. Confirm whether the utility requires its own meter enclosure, provisions integrated with service equipment, instrument transformers, a particular compartment arrangement, or designated access and sealing provisions. Establish who furnishes each metering component and where the utility’s scope ends; assumptions about a familiar arrangement may not match the requirements for a specific service.

Provide the applicable utility service manual, metering detail, service application requirements, and any utility-reviewed drawings with the inquiry when available. Ask the utility to confirm acceptable equipment interfaces and metering locations before release for manufacture. The quoted configuration, component availability, and any documentation associated with the meter provisions remain subject to project review and confirmation.

Specify the Main Disconnect and Service Protection

The main disconnect must suit the service arrangement and the facility’s distribution plan. Define whether the project calls for a single main device or another approved arrangement, the required switching and overcurrent functions, the connection scheme, and the intended downstream feeders. Equipment selection also depends on project-specific electrical ratings and fault-current information; these parameters should come from the responsible engineer and utility rather than being assumed from the voltage designation.

Share the one-line diagram, available fault-current information, protection requirements, and any coordination constraints when requesting pricing. Identify whether the equipment must interface with existing distribution and provide drawings or verified dimensions for that interface. We review the requested scope against configuration and component availability; no particular rating, device, or coordination result should be assumed until it is confirmed for the quotation.

Define Grounding and Bonding at the Service

Service grounding and bonding must reflect the actual source arrangement, service point, and governing design requirements. Clearly distinguish the grounded conductor from equipment grounding and bonding paths in the project documentation, and show where the service bonding connection is intended. The equipment design cannot resolve an undocumented grounding scheme, and a generic four-wire description is not enough to settle every project-specific connection.

Include the grounding detail and relevant notes from the electrical design, including the intended treatment of the neutral and equipment enclosure. Identify any existing grounding connections that a replacement assembly must accommodate. The engineer of record and other responsible project professionals should resolve the design and code questions; installation, testing, and energization require qualified personnel following approved procedures.

Match Service Conductors and Physical Interfaces

Conductor terminations and routing affect both the equipment configuration and its fit at the service location. Provide conductor material, quantity, size, insulation, and termination requirements as established by the project design, along with the direction of entry and available bending or access space. Also document lug or termination preferences where specified, and distinguish incoming service conductors from outgoing conductors so the connection scope is clear.

For retrofit work, submit verified field dimensions, existing connection details, enclosure constraints, and photographs or drawings that explain the interface. Identify what is being replaced and what must remain, including any transition points between new and existing equipment. We supply new equipment and new retrofit components only; suitability for an existing installation depends on review of the documented configuration and dimensions.

Confirm U.S. Availability, Standards, and Submittals

A 347/600 V designation is not by itself proof that a particular configuration is available or suitable for a U.S. project. Confirm the serving utility accepts the proposed service and metering arrangement, and verify equipment availability, engineering, component origin, and lead time with the project quotation. Customers may specify American components; component origin and any domestic-content requirements must be addressed and confirmed for the quoted scope rather than presumed.

A useful procurement package includes the one-line diagram, utility requirements, equipment schedule, grounding detail, conductor information, fault-current data, site and interface dimensions, and requested submittals. Ask which standards apply to the proposed configuration and verify listing requirements for the equipment being quoted. UL 891 applies to switchboards, not universally to all switchgear; listing and applicable standards must be confirmed for the specific assembly.

LET'S BUILD SOMETHING

Start with
the details.

Tell us what you’re working on. The more you can share about your project, the better we can begin the conversation.

PROJECT INQUIRY

Request a quote

This form opens your default email application. Your inquiry is sent only when you send the email. You can also email us directly or call our team.

* Required fields

Request a quote