347/600 V Switchboards

347/600-Volt Switchboards

Switchgear Builders Texas manufactures new 347/600-volt switchboards to project specifications, serving Texas from the United States and shipping nationwide. This voltage class is commonly associated with a three-phase, four-wire wye system, but the utility service, equipment ratings, and connected loads must be confirmed for each project. We review the one-line diagram, schedules, and site requirements to define a suitable assembly and identify open design questions before providing a quotation.

UL 891 switchboardsMADE IN USAFAST lead times
NEW EQUIPMENT. PROJECT FOCUSED.SERVING TEXAS
Electrical switchgear lineup in a workshop

NEW SWITCHGEAR FOR YOUR PROJECT

MANUFACTURING / EQUIPMENT / TEXAS

Coordinate the 600 V System and 347 V Loads

A 347/600 V designation describes a system with 600 V between phases and approximately 347 V from phase to neutral in a three-phase, four-wire wye configuration. Confirm that this is the intended service arrangement rather than relying on a panel schedule label alone. The utility service details, available conductors, grounding method, and project one-line should all tell the same story before the switchboard is specified.

List every load by supply voltage and phase, including line-to-neutral lighting or other 347 V loads and line-to-line 600 V equipment. Identify any loads requiring a different voltage, frequency, or source arrangement. These details help determine feeder assignments and device configurations, and reveal whether additional distribution or transformation is part of the project. We use the project documents to scope new equipment; the final design depends on engineering review.

Match Bus and Protective Device Voltage Ratings

The switchboard bus rating and each protective device’s voltage rating must be suitable for the system and the intended circuit. Specify the nominal system voltage, phase and wire count, service or distribution function, and the required continuous-current capacity for the assembly. Do not assume that a device described simply as a 600 V breaker is interchangeable with every device or arrangement used in a 347/600 V system.

Provide the available fault-current information and the project’s required short-circuit rating so that the assembly and protective devices can be reviewed as a coordinated configuration. Note any specified selective-coordination, arc-energy, or protection requirements in the documents rather than leaving them implicit. Fault-current data and device selection require project-specific engineering; ratings, device compatibility, and applicable standards are confirmed during quotation review.

Choose Pole Configuration by Circuit

Pole count follows the connected circuit, not just the switchboard’s overall voltage label. Three-phase 600 V feeders commonly call for three-pole devices, while 347 V line-to-neutral branch circuits need an arrangement suited to the required phase and neutral connections. Identify each feeder’s voltage, phase, number of conductors, and whether the neutral must be switched or remain continuous under the project design.

Circuit schedules should state breaker or other protective-device type, pole count, frame or trip requirements where defined, and the quantity of spare or future positions. If a feeder serves mixed loads or includes a special switching requirement, mark that clearly on the one-line and schedule. We review the requested devices as part of the new switchboard build; selection and availability are subject to configuration review and quotation.

Define Conductor Terminations Before Release

Termination requirements affect the switchboard’s arrangement and should be supplied with the electrical schedules. For each incoming and outgoing connection, document conductor material, quantity per phase, conductor size and insulation range, and whether the connection is made with lugs, bus, or another specified method. Include entry direction and cable or conduit routing constraints, since top, bottom, front, or rear access can influence the layout.

Also identify any required lug orientation, termination space, cable bending constraints, and limits imposed by the electrical room or installation drawings. Do not treat a generic ampere rating as a complete termination specification. Confirm that the proposed connection method and device terminals are compatible with the conductors and project requirements. Field installation and termination must be completed by qualified personnel using approved procedures and equipment documentation.

Specify Neutral and Grounding Requirements

A three-phase, four-wire wye system includes a neutral, but neutral treatment depends on the connected loads and grounding design. State whether the switchboard requires a full-capacity or otherwise engineered neutral bus, identify circuits that use 347 V line-to-neutral power, and describe any expected nonlinear loads that may affect neutral loading. The engineer of record should define the neutral and grounding arrangement from the load and system design.

Clarify how the neutral is handled at the service equipment and at downstream distribution, including any required bonding or isolation arrangement shown in the project documents. Grounding conductors, equipment grounding provisions, and neutral connections should be distinguished in the schedules and one-line. We do not infer these design choices from voltage alone; provide the applicable drawings and specifications so the configuration can be reviewed before pricing.

Confirm Utility Fit, Documentation, and New Equipment Scope

Confirm with the serving utility that a 347/600 V service is available for the project and verify the service configuration, metering requirements, point of connection, and any utility-specific equipment constraints. Utility availability and acceptance vary by site and provider; a voltage designation on a project drawing does not establish that the service can be supplied. Share utility documents and requirements early so they can be considered in equipment scoping.

For a complete quotation, provide the one-line diagram, panel and feeder schedules, specifications, available fault-current data, room layout, cable-entry requirements, and requested documentation. We supply new switchboards and new retrofit components only; any retrofit scope must identify the existing equipment and interfaces for review. Availability, engineering, component origin, lead time, testing documentation, listing, and applicable standards must be confirmed for the quoted configuration. UL 891 applies to switchboards, and its applicability should be verified for the specific assembly.

LET'S BUILD SOMETHING

Start with
the details.

Tell us what you’re working on. The more you can share about your project, the better we can begin the conversation.

PROJECT INQUIRY

Request a quote

This form opens your default email application. Your inquiry is sent only when you send the email. You can also email us directly or call our team.

* Required fields

Request a quote