Electrical Distribution Glossary

Selective Coordination: Electrical Distribution Glossary

Selective coordination is the intended arrangement of overcurrent protective devices so that, for a fault on a branch circuit or downstream feeder, the device nearest the affected circuit interrupts the fault while upstream devices remain closed when the design permits. The result is not guaranteed by choosing devices with similar ratings or by specifying a particular switchboard. It depends on a qualified study of the actual system, equipment, settings, and available fault current. Switchgear Builders Texas manufactures and supplies new equipment and new retrofit components to specification, serving Texas from the United States and shipping nationwide.

UL 891 switchboardsMADE IN USAFAST lead times
NEW EQUIPMENT. PROJECT FOCUSED.SERVING TEXAS
Electrical switchgear cabinets on a manufacturing floor

NEW SWITCHGEAR FOR YOUR PROJECT

MANUFACTURING / EQUIPMENT / TEXAS

What selective coordination means

In a selectively coordinated distribution system, protective devices are evaluated in series along each relevant path from the source to the load. The design objective is to limit an overcurrent interruption to the device closest to the fault, preserving service to unaffected portions of the system where the protection design and fault conditions allow. Coordination is therefore a system-level performance objective, not a stand-alone feature of one breaker or switchboard.

The term does not mean that every fault will affect only one circuit under every possible operating condition. Device operation depends on fault magnitude, duration, device characteristics, settings, and the configuration in service. A coordination study must identify the circuits and operating scenarios being evaluated and determine whether the intended device selectivity is achieved. Ask the engineer which portions of the distribution system and which source configurations are included in the study.

How protective devices are evaluated

A qualified engineer commonly compares time-current characteristics for upstream and downstream overcurrent devices, using applicable device data and the system’s calculated fault-current conditions. The evaluation considers whether a downstream device can clear a fault before an upstream device also trips or opens. Depending on the equipment and design, relevant inputs may include breaker type, trip unit, adjustable settings, fuse characteristics, and manufacturer-published selectivity information.

A curve comparison alone may not resolve every case, particularly where high fault currents, current-limiting behavior, or device-specific limits affect the result. The study’s methods and assumptions should be documented, including the source data used and any boundaries on the conclusion. For procurement, provide the engineer’s device schedule and study requirements early so the proposed new equipment can be reviewed against the intended protective-device arrangement.

System conditions that can change the result

Coordination depends on the system that will actually operate, not just on a nominal one-line diagram. Utility source conditions, transformer impedance, conductor lengths and sizes, generator operation, tie-breaker positions, and alternate feeds can affect calculated fault current and protective-device response. A device arrangement that is selective in one operating mode may not meet the same objective in another mode, so the engineer should identify normal and alternate configurations that matter to the project.

Changes made after the study can also alter its conclusions. Replacing a breaker with a different type, changing trip settings, adding a generator, or revising a feeder may require engineering review. When requesting pricing for new equipment or new retrofit components, identify known system changes and provide the latest one-line diagram, available fault-current information, and required settings or device characteristics. Confirm that submitted component information matches the configuration evaluated by the qualified engineer.

Study scope and project records

A useful coordination study defines its scope clearly: the source and downstream devices analyzed, applicable operating modes, fault-current assumptions, and the design criteria used to judge selectivity. It should identify device types and relevant settings, show time-current comparisons where appropriate, and explain any limitations or unresolved coordination intervals. Responsibility for the study and approval of protective settings should be assigned to qualified electrical engineering personnel, not assumed from an equipment quotation.

Keep the final study aligned with approved construction documents and the equipment actually furnished. Request the submittal information needed for the engineer to verify the proposed configuration, such as device identification, trip-unit or fuse data, and available manufacturer documentation. Availability, component origin, engineering, lead time, and test documentation are confirmed for each quotation. Listing and applicable standards must also be verified for the specific equipment configuration; UL 891 applies to switchboards, not universally to all switchgear.

Specifying new equipment and retrofit components

For a new switchboard or related distribution equipment, provide the source arrangement, system voltage, calculated or available fault-current data, feeder and branch-circuit requirements, and the protective-device schedule. State the coordination objective and identify any loads or systems where continuity is especially important. Also ask the engineer to define required device settings and acceptable alternatives before procurement, since substituting a device can change the study result.

For a retrofit, identify the existing equipment, bus and compartment details, device type, frame or mounting requirements, and the intended circuit position. Provide clear equipment nameplate information and current drawings where available; do not assume that a component will fit or preserve coordination based on a similar catalog description. We supply new equipment and new retrofit components only, built or selected to specification following project review. Installation, servicing, testing, and energization require qualified personnel using approved procedures.

Practical limits and purchasing decisions

Selective coordination is one consideration within a broader protection design. The engineer may need to balance selectivity with conductor and equipment protection, arc-flash objectives, reliability needs, and applicable project or code requirements. The buyer should ask which devices and fault levels are covered, whether the conclusion changes under alternate sources, and what field settings must be verified before the system is placed in service. No equipment description by itself establishes the study outcome.

When requesting pricing, send the current one-line diagram, equipment schedules, study criteria, required component specifications, and the project’s documentation expectations. Identify whether the request is for new equipment or new retrofit components and note any design decisions still awaiting engineering review. We serve Texas from the United States and ship nationwide. A quotation can address the specified configuration, while coordination conclusions remain dependent on the qualified study and the final installed system.

LET'S BUILD SOMETHING

Start with
the details.

Tell us what you’re working on. The more you can share about your project, the better we can begin the conversation.

PROJECT INQUIRY

Request a quote

This form opens your default email application. Your inquiry is sent only when you send the email. You can also email us directly or call our team.

* Required fields

Request a quote