Blanking and punching: establish the panel geometry
Blanking creates the panel outline and major edges; punching produces openings for devices, ventilation, cable entry, fasteners, and other specified interfaces. These operations begin with the released drawing dimensions, not assumptions based on an existing enclosure. Define the panel datum, finished dimensions, material and thickness, edge conditions, and the location of each opening from shared reference points. A consistent datum helps coordinate enclosure parts with the switchboard arrangement and installation drawings.
Cutout accuracy depends on more than nominal width and height. The drawing should identify shape, corner treatment, orientation, spacing, and any required clearance around the intended device or fitting. Confirm whether dimensions refer to the opening itself, a centerline, or its distance from a finished edge. If a component manufacturer provides a cutout drawing, include the applicable revision and confirm that it matches the selected component before releasing the enclosure layout.
Cutout coordination with electrical and field interfaces
Panel openings must be coordinated with the electrical design and the equipment that passes through or mounts to them. Review device dimensions, mounting patterns, cable routes, conduit or bus interfaces, barriers, and access requirements as a coordinated arrangement. A cutout may be dimensionally correct yet conflict with nearby hardware or reduce the space needed for installation and service. Mark these relationships on the enclosure drawing so review covers both the opening and its surrounding clearances.
For field-facing panels, identify which interfaces are fixed by the project and which remain subject to engineering review. Specify door swing, removable-panel boundaries, operator access, and the intended locations of incoming and outgoing connections where applicable. Provide the relevant equipment layout and interface details with a pricing request. This gives us a basis to assess the proposed fabrication scope and identify missing dimensions or conflicts before the drawing is approved for production.
Bend allowances and formed-panel dimensions
A flat blank does not have the same dimensions as the finished formed part. Bend allowance and bend deduction affect the relationship between the flat pattern, bend lines, outside dimensions, and finished returns. The values depend on factors such as material, thickness, bend angle, tooling, and the specified inside radius. Drawings should distinguish flat-pattern dimensions from finished-part dimensions and state the controlling dimensions for the assembled enclosure.
Formed geometry also affects mounting surfaces, door edges, corner alignment, and the position of cutouts near a bend. Review the required flange depth, return direction, angle, and bend sequence where those details influence fit or access. Openings close to a bend may need particular attention because forming can affect their shape or location. We review these details against the project requirements; final allowances and manufacturability depend on the selected material and configuration.
Fit-up: verify how panels meet as an assembly
Fit-up concerns the relationship between individual panels and the enclosure as a whole. Review seams, corners, fastening points, door and cover interfaces, mounting surfaces, and the alignment of adjacent sections. A useful drawing set shows how each fabricated part locates relative to the assembly, rather than leaving the final position to interpretation. Where the enclosure connects to other equipment or a site interface, identify the mating dimensions and clarify which party supplies each connecting detail.
Tolerance decisions should reflect the function of each feature. A device opening, a row of mounting holes, and a nonfunctional exterior edge may not require the same dimensional control. Identify critical dimensions and acceptable variation in the project documentation, and flag features whose position must align with separately supplied equipment. Fit-up review can then focus on those interfaces and on repeatable assembly, without treating every edge as an equally critical electrical or mechanical reference.
Repeatable dimensions and drawing control
Repeatability starts with a stable, coordinated set of approved documents. Identify the drawing revision, part references, quantity, and any project-specific changes that apply to each enclosure panel. Avoid mixing dimensions from an early layout with cutout information from a later component selection. When a change affects a hole pattern, opening, bend, or mating edge, show the revision clearly and review related parts for knock-on effects before the updated design is released.
For projects with multiple similar panels, state which dimensions and features are common and which differ by section or application. Referencing a controlled master drawing can reduce ambiguity, but it should not conceal unique field interfaces or equipment arrangements. Submit relevant device cutout drawings, approved layouts, and interface schedules with the package. This documentation supports a focused engineering review and helps ensure that quoted fabrication reflects the intended new equipment or new retrofit component.
Scoping new equipment and retrofit components
A pricing request should describe the enclosure scope in enough detail to review both fabrication and fit. Include the application, required quantity, panel or assembly drawings, material and finish requirements, cutout schedule, formed dimensions, and the equipment that must mount to or connect with the enclosure. Identify any dimensions that must match existing field interfaces, while distinguishing those interfaces from the new components we are supplying. Project requirements, engineering review, component origin, and lead time are confirmed for each quotation.
For a retrofit, specify the new replacement component and the dimensions it must meet; do not assume that an unverified field measurement is a complete fabrication drawing. Provide reference photos or site measurements as supporting information, with measurement points identified and critical interfaces called out. We manufacture and supply new equipment and new retrofit components. Applicable standards and any requested listing must be reviewed for the complete configuration; UL 891 applies to switchboards, not every switchgear assembly.
